G220, M80, M83 and M21

[Per-Bear]

Re: G220, M80, M83 and M21

7006 =Red
8006 =Yellow
9006 =Tan

Thanks!!

[Ivan Rajic]

Re: G220, M80, M83 and M21

You'll need one more of these...

http://www.cleanyourcar.co.uk/polishing/meguiars-buffing-pads/meguiars-6-5-softbuff-polishing-pad/prod_204.html

And I can't seem to find the bonnets on the site that you've linked. But look to the bottom of this page, and these are what you will need, just not sure where to get them in your country...

http://autodetailingsolutions.com/Microfiber%20Towels.htm

Hope this helps,
Nick

A little off topic.. Nick, are those supreme shine mf towels the one that come with the smooth surface clay kit? I just ordered a few from ads.com hoping those were it, since it's hand down the best towel I've ever used...

[Nick Chapman]

Re: G220, M80, M83 and M21

A little off topic.. Nick, are those supreme shine mf towels the one that come with the smooth surface clay kit? I just ordered a few from ads.com hoping those were it, since it's hand down the best towel I've ever used...

Yes, those are the same towels.

Do I hear a sigh of relief?

[Ivan Rajic]

Re: G220, M80, M83 and M21

Yes, those are the same towels.

Do I hear a sigh of relief?

I just got back from jumping around the house yelling "YEEEESSSSSSSSS!!!!"

[Per-Bear]

Re: G220, M80, M83 and M21

Nick, check my autogeek link

[Per-Bear]

Re: G220, M80, M83 and M21

I can also just use M80 and the M21?

That will be ok?

[J. A. Michaels]

Re: G220, M80, M83 and M21

Yes you can. Remember Meguiars teaches you to use the least aggressive first. So it would be #80, then #83, then your lsp. In your example #21. Good luck.

[Per-Bear]

Re: G220, M80, M83 and M21

Okai.

I have a car with just a little swirls, so Ill try with 80 first, then seal with 21 if the swirls are gone.

That would be nice I hope.

[J. A. Michaels]

Re: G220, M80, M83 and M21

Good luck. That is the way I would tackle it.

[Markus Kleis]

Re: G220, M80, M83 and M21

Okai.

I have a car with just a little swirls, so Ill try with 80 first, then seal with 21 if the swirls are gone.

That would be nice I hope.

Great plan.

Also remember that often times with the G110 (Or most if not all polishers) you will likely need several passes. If you make one pass with 80 and still see some swirls that doesn't necessarily mean that it isn't still your best choice. Try it another time and check it again.

It isn't uncommon to need 3-4 passes on stubborn swirls sometimes.

good luck!

[Per-Bear]

Re: G220, M80, M83 and M21

I love my G220..

Thanks for the tips and help both of you!

[Ivan Rajic]

Re: G220, M80, M83 and M21

Yes you can. Remember Meguiars teaches you to use the least aggressive first. So it would be #80, then #83, then your lsp. In your example #21. Good luck.

#80 should come after #83 and before LSP... unless you were saying first try #80, then #83 to remove defects... in which case you'll follow #83 with #80