Tweet
After wiping down the hard plastic and door panels with apc+ 10:1, do you usually follow with a damp clean mf to remove any residue or is it insignificant to the point a protectant will take care of it?
- If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
-
2018 Subaru Outback 3.6R Touring - Crystal White Pearl -
Re: Wipedown w/ mf needed after APC+ 10:1?
Well, If I was using a lot of APC, I would be sure to dry off excess.
Usualy I dont need to much, so I just apply then just use the protectant.2017 Subaru WRX Premium - WR Blue -
Re: Wipedown w/ mf needed after APC+ 10:1?
My guess is most people don't, hey go right to the protectant/dressing.Originally posted by Hellspawn View Post
If you like, you could wipe down with a light cleaner and this will insure any residue is removed.
Try either Quik Interior Detailer Spray or Quik Interior Detailer Wipes.
Comment
-
Re: Wipedown w/ mf needed after APC+ 10:1?
ok I usually do use something afterwards, the mf I used with the apc+ left the surface just damp, so I'll probably just hit with some protectant then. I would imagine if I was using 4:1 then I'd want to wipe down then.Originally posted by Mike Phillips View PostMy guess is most people don't, hey go right to the protectant/dressing.
If you like, you could wipe down with a light cleaner and this will insure any residue is removed.
Try either Quik Interior Detailer Spray or Quik Interior Detailer Wipes.
2018 Subaru Outback 3.6R Touring - Crystal White PearlComment
-
Re: Wipedown w/ mf needed after APC+ 10:1?
I use APC then go straight to dressing, if i see any residue i either re apply APC or use QID like Mike suggestedNick
Tucker's Detailing Services
815-954-0773
2012 Ford Transit ConnectComment
-
Re: Wipedown w/ mf needed after APC+ 10:1?
Seems like I must be the only one that does go over the areas with a damp towel after using an APC on vinyl. plastic or leather.
Takes very little time and I then feel like I have done a better job of cleaning.
Seems to be another case of "Whatever works for you".
Charles
The RainmakerComment
-
Re: Wipedown w/ mf needed after APC+ 10:1?
what your doing is fine and is probably good. I just never really seen APC leave a residue.Originally posted by CharlesW View PostSeems like I must be the only one that does go over the areas with a damp towel after using an APC on vinyl. plastic or leather.
Takes very little time and I then feel like I have done a better job of cleaning.
Seems to be another case of "Whatever works for you".Nick
Tucker's Detailing Services
815-954-0773
2012 Ford Transit ConnectComment
-
Re: Wipedown w/ mf needed after APC+ 10:1?
I always rinse when using cleaners. Just habit I guess.
Nothing wrong with it. Today I was working on leather seats and APC+, agitate, rinse, rinse wipe down. When it was dry, I liberaly sprayed GC leather cleaner/conditioner on to treat them
Philippians 2:14 - Do all things without grumbling or questioning,Comment
-
Re: Wipedown w/ mf needed after APC+ 10:1?
What you you mean by "rinse, rinse wipe down"? Damp microfiber to get off the residue?Originally posted by Nappers View PostI always rinse when using cleaners. Just habit I guess.
Nothing wrong with it. Today I was working on leather seats and APC+, agitate, rinse, rinse wipe down. When it was dry, I liberaly sprayed GC leather cleaner/conditioner on to treat themComment
Comment