Originally posted by aris
View Post
I would have rather cleaned the floor liners than the carpet. lol.
- If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
-
Re: Mazda 3
That should protect the carpet well, I did a work truck a year ago with super clean carpet but extremly dirty weather tech floor liners.
I would have rather cleaned the floor liners than the carpet. lol. -
Re: Mazda 3
Originally posted by speed3blackmica View Posti came up with a solution for my 3 a while back...i switched to the rubber matts
lol but nah i do understand it is a lil weird to clean. great job tho nick
I use the OEM rubber ones in summer and weather tech floor liners for winterLeave a comment:
-
Re: Mazda 3
i came up with a solution for my 3 a while back...i switched to the rubber matts lol but nah i do understand it is a lil weird to clean. great job tho nick
Leave a comment:
-
Re: Mazda 3
I own a mazda 3 and yes it's a pain...find if you keep it clean all the time it's much easier to clean..but if you leave it to long it's a painLeave a comment:
-
Re: Mazda 3
Unfortunately, I don't really have a solution. The problem is that there's not any good nap to it. I'm sure you noticed that if you brush it, it just frays the carpet. It's just junk, plain and simple. I guess my only "trick" is to avoid it or educate the customer on it and make sure their expectations on that part of the detail aren't very high.
Leave a comment:
-
Re: Mazda 3
Nice work Nick! We have a 2005 Mazda3 hatch similar to that one. The carpet in the Mazda3's is some of the worst I've ever seen in a car. It's worse than a lot of trunk carpeting out there. I've even thought about replacing mine with a high quality after-market carpet.
Again, great work!Leave a comment:
-
Re: Mazda 3
No,Originally posted by CieraSL View Post
but I dont blast the engine with a pressure washer like I have seen others do.
A light stream of water is usually good enough, followed by an application of APC and a soapy water agitation with various brushes, then I lightly rinse all soap away and dry the main areas with a big cotton towel. Then I start the vehicle and let it run for 7-10 minutes.
After the vehicle is washed and dried I spray the engine with Hyperdressing at 2:1 and wipe it down with a cotton towel soaked in Hyperdressing, wipe all painted areas down with M135. I then go over any small crevices with a paintbrush that may have any dirt remnants in them. Sometimes I spray the underhood pad with Hot Shine Tire Foam as well. I have a bunch of other little steps as well.
Works great for me,
Leave a comment:
-
Re: Mazda 3
Originally posted by CieraSL View Post
Yes, I do them on my more extensive details. I do not do the engine if its just a basic detail. I charge extra to do the engine as well.
I am doing fifteen basic details for a local doctor's office, just a one step cleaner wax on the exterior and the interior detailed. It would have cost a lot more in the long run to pay $30 per car for the engine done, plus I only have a certain amount of time.
I think you have seen engine pics in some of my writeups though....
2008 Cadillac Escalade
2008 Chrysler Town & Country
2004 Mercedes Benz E320 - Complete Detail
2001 Volvo S80 - Engine,interior,and exterior cleanupLeave a comment:
-
Re: Mazda 3
Do you typically do the engine on your more extensive details? I just realized that I never see any engine pics in your writeups. I don't like to do much more to engines beyond a basic wipe down if they are lightly dirty - guess I'm just fearful of screwing up something up.Leave a comment:
Leave a comment: